When choosing hydraulic parts, check three things first: matching of pump and engine power, matching of valve and actuator flow, and consistency of mounting interface dimensions. When replacing pumps or valves on a used excavator, it is better to spend an extra 2,000 yuan on an original factory dismantled part with a test report than to save money on a refurbished part with unknown parameters. Below, we break it down by selection, faults, maintenance, and export inspection—all lessons learned the hard way in the market.
Hydraulic Pump Selection: Displacement and Pressure Matching Are the Bottom Line
Excavator hydraulic pumps are mainly divided into two types: piston pumps and gear pumps. Most 20-ton class used excavators use swashplate piston pumps, with rated pressure mostly in the 34–38 MPa range. When selecting, first confirm the original pump's displacement (ml/r) and control method (negative flow, positive flow, or load sensing). If you change the pump without changing the control logic, the machine will have jerky movements and engine stall. On the market, original factory dismantled piston pumps for 20-ton class machines are roughly 8,000–18,000 yuan, with those having complete test reports costing two to three thousand more; domestic brand-new replacement pumps can be had for 4,000–9,000 yuan, but pressure stability and service life are a notch lower. Before buying, ask the supplier to provide the pump's factory serial number and pressure test curve. Without these two, don't touch it no matter how low the price.

Motors and Multi-Way Valves: When Flow Doesn't Match, Movement Feels Weak
Common faults in travel motors and swing motors are internal leakage, manifested as unilateral deviation and weak swing. The diagnosis is simple: after the machine is warmed up, measure the return oil flow; if it exceeds the rated value by 15%, internal leakage can basically be confirmed. For multi-way valve selection, focus on nominal diameter and rated flow. The main valve diameter of a 20-ton class excavator is mostly around 32 mm. If flow matching deviation exceeds 10%, compound movements will noticeably lose speed. Used multi-way valves cost about 3,000–9,000 yuan. Parts with worn spools or scratched valve bodies are not recommended for repair and reuse, as repair costs often approach the price of replacement. In export orders, customers in the Middle East and Southeast Asia have requirements for the sealing material of multi-way valves; for high-temperature regions, fluorine rubber seal versions are recommended.
Common Faults: Check the Oil First, Then Tear Down the Pump and Valve
Eighty percent of hydraulic system faults stem from the oil. When oil temperature exceeds 80°C and oil cleanliness is below NAS Class 9, the wear rate of pumps and valves increases exponentially. The correspondence of common faults is roughly as follows:
- Slow movement, engine stall: first check pilot pressure and filter clogging, then check the pump's flow control mechanism;
- Cylinder drift: mostly cylinder internal leakage or counterbalance valve failure; don't rush to replace the pump;
- System abnormal noise: air intake in the suction line or incorrect oil viscosity, especially common in winter;
- High oil temperature: clogged radiator, slipping fan belt, overflow valve stuck open—check item by item.
Before disassembling the pump, perform pressure and flow tests and keep the data on file. Many customers replace a good pump thinking it's bad, when the problem actually lies in the pilot pump or filter. This kind of misdiagnosis is very common in used equipment transactions.
Daily Maintenance: Three Hard Rules
- Replace hydraulic oil every 2,000 hours or once a year; replace the filter element at the first 50 hours, then every 500 hours; in dusty conditions, shorten to 250 hours;
- Perform a cleanliness test at every oil change; install new parts only when cleanliness is NAS Class 9 or better, otherwise the new pump will wear just the same;
- For equipment idle for long periods, start and run it once a month and exercise all cylinders to prevent valve spool corrosion and sticking.
In parts procurement, there is a clear price gap among three tiers: original parts, brand aftermarket parts, and dismantled parts. Taking the main pump of a 20-ton class excavator as an example, a brand-new original part costs about 30,000–50,000 yuan, a brand aftermarket part 15,000–25,000 yuan, and an original dismantled part 8,000–18,000 yuan. In used construction machinery export scenarios, dismantled parts offer the best cost-performance, but must be accompanied by pressure test records and appearance inspection photos; otherwise, overseas customers may dispute acceptance.
Export Inspection: Hydraulic Parts Need Separate Reports
For construction machinery export, it is best to have separate test reports for hydraulic parts rather than mixing them into the whole-machine report. The report should include at least three items: pressure holding test, flow test, and seal check. For shipments to Africa and Southeast Asia, wooden crates with moisture-proof film are recommended, as sea transport salt spray can significantly corrode valve body surfaces. Before shipping, record a video of the pump shaft rotation and valve spool movement as after-sales evidence. For export orders handled by Sanqi Machinery, the after-sales dispute rate is noticeably lower when hydraulic parts are packed and numbered separately.
For a used excavator hydraulic pump, should I choose an original dismantled part or a domestic new part?
It depends on usage intensity and budget. For machines under 20 tons and annual working hours within 1,500, original dismantled parts offer high cost-performance, but a pressure test report is required; for high-intensity working conditions, brand aftermarket new parts are recommended for more controllable service life.
After replacing the hydraulic pump with a new one, the movement is still slow. What is the usual cause?
Mostly insufficient pilot pressure or improperly adjusted flow control mechanism, or possibly clogged filters or excessively high oil temperature. Measure pilot pressure and system flow first; don't rush to replace the pump a second time.
What is the approximate price of a used multi-way valve, and how do I judge whether it is usable?
A used multi-way valve for a 20-ton class machine costs about 3,000–9,000 yuan. Check spool wear, valve body scratches, and sealing surfaces, and perform a flow test. Those with excessive internal leakage are not recommended for repair and use.
What documents are required for exporting hydraulic parts?
Normally, a commercial invoice, packing list, and certificate of origin are required. For hydraulic parts, test reports and pressure test records are recommended. Specific certifications depend on the destination country; for the EU, CE-related documents are required.
How often should hydraulic oil be changed, and what is the cleanliness standard?
Generally every 2,000 hours or once a year; in dusty conditions, shorten to 1,000–1,500 hours. Cleanliness should be controlled within NAS Class 9, and filters should be replaced at the same time as the oil change.


Post Comment 1