If hydraulic parts are selected incorrectly, even the best pump is useless; if maintenance cannot keep up, even original parts will be scrapped prematurely. More than 70% of hydraulic system failures in used excavators are concentrated in three areas: piston pumps, travel motors, and multi-way valves, and a considerable portion of these are caused by mismatched selection parameters or inadequate oil management, not by the quality of the parts themselves.
Why used equipment relies more on hydraulic parts matching
When imported used excavators arrive at domestic job sites, the working conditions differ greatly from those in their country of origin. Most 20-ton machines in Japan are configured for short-boom, light-load work, but in domestic mines and sand and gravel yards they are often put to heavy work. The hydraulic system runs under high pressure and high temperature for long periods, and the wear rate of the pump swashplate and piston pairs accelerates noticeably. If you only seek cheap replacements at this point and casually fit a pump with similar flow, the pressure compensation and power regulation curves will not match, the operation will feel sluggish, and fuel consumption will rise.

Among the used machines we handle, parts commonality is relatively good for the Komatsu PC200, Caterpillar 320, and Hitachi ZX200 series. The market price for remanufactured hydraulic pump assemblies is roughly 12,000 to 28,000 RMB, while new original parts exceed 40,000 RMB; remanufactured travel motor assemblies are 6,000 to 15,000 RMB; and multi-way valves, depending on the number of circuits, range from 8,000 to 20,000 RMB for the main valve. The large price differences mainly come down to the degree of spool wear and whether pressure bench testing has been performed.
Key points for selecting hydraulic pumps, motors, and multi-way valves
- Hydraulic pump: First confirm displacement, rated pressure, and control method (negative flow, positive flow, or load sensing); none of the three can be omitted. Installing a pump with the same displacement but a different control method will noticeably worsen operational coordination.
- Travel motor: Check the reduction ratio and brake valve type; for two-speed motors, also verify the shift pressure. Used parts must be tested under no-load and load conditions, listening for abnormal noise and checking whether the return oil is clean.
- Multi-way valve: Select according to the number of circuits and flow, with emphasis on verifying the relief valve setting and the condition of the compensation valve. Do not touch parts with scored spools; repair costs are often close to replacement.
- Cylinders and seals: For seals, original or well-known brand parts are recommended. If the piston rod coating is scratched by more than 0.2 mm, the rod must be replaced or re-chromed.
When selecting parts, it is best to provide the machine nameplate and hydraulic system schematic. Suppliers can then supply parts according to the drawing, which is far more reliable than verbally quoting a model number. Customers doing construction machinery export should also pay attention to voltage, oil port thread standards, and differences in local oil grades. For machines shipped to the Middle East and Africa, allow extra margin for heat dissipation and oil adaptability in advance.
Common faults and troubleshooting sequence
For slow or weak operation, first measure main pump pressure, then check pilot pressure, and finally inspect multi-way valve relief. High oil temperature is mostly caused by blocked coolers, deteriorated hydraulic oil, or severe internal pump leakage; do not rush to replace parts. For travel deviation, first swap the left and right motor oil lines to determine whether the problem is the motor or the main valve. If system noise is accompanied by blackened oil, it can basically be determined that the piston pairs or valve plate are worn and need to be disassembled for inspection.
There is a rule of thumb in maintenance: when both the pump and motor show internal leakage, it is advisable to evaluate them as a pair. Replacing only one often leads to the other failing a few months later, and downtime losses are more expensive than the parts.
Key daily maintenance actions
- Change hydraulic oil every 500 to 1,000 hours or every six months; shorten to 300 hours on dusty job sites.
- Check the suction filter and return filter every 250 hours; do not ignore filter differential pressure alarms.
- Regularly test oil cleanliness; if it exceeds NAS 9, consider filtration or oil replacement.
- For used equipment that has been idle for a long time, manually turn the engine over and warm up at low speed before starting to avoid dry friction.
Frequently Asked Questions (FAQ)
Can remanufactured hydraulic pumps for used excavators be used with confidence?
The key is whether core wear parts such as piston pairs and valve plates have been replaced and whether pressure bench testing has been performed. Remanufactured parts with test reports and a warranty of at least six months usually offer better value than dismantled parts without documentation.
Is it more cost-effective to choose original or aftermarket hydraulic parts?
For safety-related parts and high-pressure core components, original or first-tier brand parts are recommended; for non-critical auxiliary parts, qualified aftermarket parts can be used. When exporting complete machines, original parts are less troublesome for customs clearance and after-sales claims.
What is the approximate cost of repairing an excavator multi-way valve?
Repairing a single circuit spool and replacing seals costs about 2,000 to 5,000 RMB; full valve remanufacturing ranges from 8,000 to 20,000 RMB depending on the number of circuits. If the valve body is cracked or severely scored, direct replacement is more economical.
How should hydraulic parts be supplied when exporting used construction machinery?
It is recommended to prepare a set of wear-prone seals and filters by complete machine model and ship them with the machine; commonly used pumps and valves can be shipped in separate boxes. Confirm the destination country's oil grade and thread standards in advance to avoid mismatch after arrival at port.
How often should hydraulic oil be changed to be safe?
Under normal working conditions, every 500 to 1,000 hours; in heavy-load or dusty environments, every 300 to 500 hours. Base the decision on oil test results; if cleanliness exceeds the limit or water content rises, change the oil earlier.


Post Comment 0